Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Styles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Metal Roof Installation Cost in Corona?
Metal roof installation in Corona typically runs $18,500 to $42,000 for a full residential tear-off and replacement, with most single-family homes landing in the $22,000 to $31,000 range. That works out to roughly $900 to $1,750 per roofing square (a square is 100 square feet), depending on the metal system you pick, the pitch of your roof, and how much of the existing structure has to be repaired before we start.
The number that lands on your bid depends heavily on material choice and roof geometry. A simple low-slope roof over a 1,800-square-foot Corona home with a standing-seam panel may price considerably lower than a cut-up roof with multiple valleys and dormers. We give you an exact figure only after an on-site inspection – never off a phone guess. Free estimates are always available at (866) 942-4187.
Metal Roof Installation Cost Breakdown (2026)
Here’s how the line items typically break down for a Corona project in 2026. These are real installed ranges, not ballpark teasers.
| Line Item | Typical Range (Installed) |
|---|---|
| Standing-seam steel panels (materials + install) | $1,300 – $2,100 per square |
| Exposed-fastener corrugated panels | $900 – $1,400 per square |
| Stone-coated steel (e.g., Boral) | $1,500 – $2,400 per square |
| Aluminum or zinc panels | $1,800 – $2,800 per square |
| Tear-off and disposal of existing roof | $1,500 – $4,500 total |
| Underlayment and waterproofing membrane | $800 – $2,200 total |
| Flashing, ridge cap, and trim | $1,200 – $3,200 total |
| Deck repair (rotted sheathing, if found) | $200 – $900 per sheet |
| Permit and inspection fees (City of Corona) | $350 – $900 |
| Old roof disposal / dump fees | $600 – $1,400 |
What pushes cost to the high end? Steep pitches slow the crew and require more safety rigging. Complex roof geometry – multiple hips, valleys, and penetrations – drives up labor and trim cost. Two-story access adds staging time. And if the deck underneath is soft, the tear-off reveals it, and we’re replacing sheathing before panels go down. What pulls cost down? A simple gable roof, single-story access, and choosing an exposed-fastener panel over standing-seam will bring your project closer to the low end of the range.
What Affects Metal Roof Installation Pricing in Corona
- Metal type and profile. A corrugated steel panel and a stone-coated Boral tile look nothing alike and price very differently. Stone-coated steel gives you the look of Spanish tile – worth considering in Corona, where so many homes were built with clay or concrete tile profiles. Standing-seam is the clean, high-end option; exposed-fastener panels cost less but need occasional fastener attention.
- Roof pitch and complexity. A 4:12 pitch can be walked with care. An 8:12 or steeper roof means more rigging, more time, and more labor. Every valley, dormer, skylight, and chimney adds flashing work that has to be done right the first time.
- Corona’s heat and sun exposure. Inland Empire sun is unforgiving. We always spec a reflective “cool roof” coating on metal here – it keeps attic temperatures down in July and August and qualifies for Title 24 cool-roof credit, which the City of Corona requires for many reroof permits. This isn’t optional in our book; we build it into every bid.
- Existing roof removal. Sometimes a metal roof can go over an existing layer, but most Corona projects call for a full tear-off first. Older homes near downtown Corona often have multiple layers, and each one has to come off and be hauled away.
- Permit requirements. The City of Corona Building Division requires a reroof permit for a metal roof installation, and inspectors will check attachment and underlayment details. Permit fees run roughly $350 – $900 depending on square footage and valuation.
- Warranty tier you choose. Because we install GAF, CertainTeet, Owens Corning, IKO, Atlas, Tamko, and Boral, we can match your budget with a manufacturer-backed warranty tier from more than one brand – a mid-tier panel from Boral might carry coverage that costs considerably less than a premium panel from elsewhere. You decide how much warranty you want to pay for.
Is a Metal Roof Worth the Price in Corona?
For most Corona homeowners planning to stay in the house long-term, yes. The two things that drive metal’s value here are fire resistance and heat performance. Corona sits in a high fire-risk zone, and unlike asphalt shingles, steel and aluminum won’t ignite from a wind-blown ember. Metal also reflects solar heat instead of absorbing it the way asphalt does, which can lower summer attic temps noticeably – and that matters when you’re looking at 100°F stretches through July and August.
Metal also tends to outlast the roof it replaces. A properly installed metal roof is engineered to last decades longer than asphalt shingles, so the cost gets spread across a much longer service life. If you plan to sell within eight or ten years, you may not recoup the premium – which is why we always walk you through that math honestly before you commit. Our team installs Metal Roof Installation in Orange as well, and the material economics are the same pattern; the difference is local climate and permit rules we handle city by city.
How to Save on Metal Roof Installation
There are real ways to trim cost without cutting quality. A few that come up often here in Corona:
- Repair first if you can. If your existing roof has years of service left, a targeted repair buys you time and spreads out the eventual cost. Our inspectors will tell you honestly whether you need a full replacement now or not.
- Choose exposed-fastener panels. They install faster and cost less per square. They won’t give you the lifespan or look of standing-seam, but for a garage, patio cover, or budget-conscious whole-roof install they’re a legitimate option.
- Bundle trim and flashing complexity. If you’re adding an addition or a patio cover at the same time, the roofers are already there. One scheduled project can cover more scope per trip.
- Check for local rebates. Cool-roof metal often qualifies for energy-efficiency rebates and utility incentives. Ask us and we’ll point you to what’s available in Corona.
- Schedule in the off-season. Summer is peak season. If your timeline is flexible, spring or late fall may give you more scheduling flexibility and less strain on material timing.
We offer free estimates – call (866) 942-4187 and we’ll come out, measure, and give you a real number. No pressure, no upsell. If a repair is the smarter call, we’ll say so.
Should You Repair or Replace a Metal Roof?
Metal roofs fail differently from asphalt. Panels can loosen at fasteners, flashing can degrade, and leaks often trace to a single penetration or failed seam rather than the whole roof. Sometimes a targeted repair is all you need. But if the underlayment has failed across a large area, or you’re seeing widespread rust on a cheaper panel, partial replacement costs more in labor over time than a clean replacement.
Because we offer roof inspection as a standalone service, you can get a straight diagnosis without committing to anything. We look, we photograph what we find, and we tell you what’s actually happening. If a repair covers it, we’ll quote the repair. If it doesn’t, you’ll know why before you spend a dollar on replacement. That’s a different approach from a company whose only product is a full roof.
Do Metal Roofs Come With Warranties in Corona?
Yes, and it’s one reason to go with a contractor who handles multiple brands. Manufacturer-backed warranties on metal roofing typically cover panel integrity and finish for years, but the coverage level varies by brand and product line. A Boral stone-coated steel panel and a GAF steel panel don’t carry identical warranty terms, and the finish warranty differs between a painted panel and an unpainted aluminum one.
We install products from GAF, CertainTeed, Owens Corning, IKO, Atlas, Tamko, and Boral, which means you’re not stuck with a single brand’s warranty. We lay out the tiers, show you what each covers, and you pick the coverage that fits your situation. We don’t fabricate warranty durations – the manufacturer’s own document is what stands behind your roof.
How Long Does Metal Roof Installation Take in Corona?
Most residential metal roof installations take three to seven days depending on roof size, pitch, and complexity. A straightforward 1,800-square-foot gable roof might be finished in three or four days. A cut-up roof with multiple valleys, a steep pitch, and deck repairs can stretch toward a week. We give you a real timeline in your estimate, not a vague “couple of weeks,” and we keep you updated as the work progresses.
Weather matters. Corona’s dry season runs roughly May through October, and that’s when most installations happen. If rain is in the forecast, we pause and secure the roof – a half-finished metal roof is not something we leave exposed to the elements overnight without proper temporary waterproofing.
FAQs – Metal Roof Installation Cost
How much does metal roof installation cost in Corona? Typically $18,500 to $42,000 for a full residential replacement, with most homes landing in the $22,000 to $31,000 range. Get a real number with a free inspection – call (866) 942-4187.
Is metal roofing cheaper than asphalt shingles in Corona? No – metal costs more upfront, usually two to three times the price of an asphalt shingle roof. It lasts far longer, though, so the cost per year of service can be lower over a roof’s full life. Call us to run the numbers for your specific home.
Do I need a permit for a metal roof in Corona? Yes. The City of Corona Building Division requires a reroof permit and an inspection before the project is closed out. Permit fees typically run $350 to $900. We handle the permit process for you – just ask when you call (866) 942-4187.
Can you install a metal roof over my existing shingles? Sometimes, but most Corona projects call for a full tear-off so we can inspect the deck and install proper underlayment. Skipping the tear-off saves money now but can void the warranty and trap hidden problems. We’ll tell you which applies to your roof.
How much does a metal roof repair cost in Corona if I don’t need a full replacement? Small repairs typically run a few hundred dollars; larger flashing or panel repairs can reach into the low thousands. Our inspection tells you exactly what your roof needs – nothing more. Call (866) 942-4187 to schedule.
Get Your Corona Metal Roof Estimate
Metal roofing is a significant investment, and you deserve numbers you can actually plan around. We’ll come out, inspect the roof, measure it properly, and walk you through material options from seven major manufacturers so you can choose the roof that fits your home and budget – not ours. From a single damaged panel to a full tear-off and replacement, one call covers it. Call (866) 942-4187 for a free estimate.
Pricing reflects the Corona market as of 2026. Orange County Roofing Co offers free estimates – call (866) 942-4187.
What Our Customers Say
"He told me my roof had another five or six years in it and I should not replace it yet. He was standing there with a quote pad in his hand. That's why I'll call him when it's time."
— Carmen Castillo"Leak over the kitchen turned out to be a cracked boot around a vent pipe, not the roof itself. He showed me the photo from up there and replaced the boot for a couple hundred dollars. The company before him had quoted a full tear off."
— Sofia Hernandez"Went up in the attic first with a flashlight before going on the roof, which no other estimator bothered to do. Found the stain and worked backward from there."
— Marcus Bryant